Exp-computer ThinCD Manual de usuario

Portable CD-ROMInstallationManualThinCD SeriesFor Parallel & PCMCIA

- 10 -SOFTWARE INSTALLATIONSOFTWARE INSTALLATION FOR WINDOWS 95/98If you are inserting the PCMCIA card into your computer for the very firsttime, depe

- 11 -Windows 95 (B)If the “Update Device Driver Wizard” dialog box appears as below, itmeans your Windows 95 is version 4.00.950B, i.e. OSR 2.In this

- 12 -Windows 95 (Older Versions)The following dialog will appear. If you are using the Portable CD-ROMunder Windows 95 for the very first time and yo

- 13 -Enabling 32-bit Card SupportYour system should be ready for PCMCIA socket support prior to operatingthe Portable CD-ROM. To check whether your c

- 14 -After the PCMCIA 32-bit Card Support is installed, Windows will ask youto reboot your computer. You should now refer to the previous section for

- 15 -SOFTWARE INSTALLATION FOR WINDOWS NTBefore You Begin♦ Be sure the Windows NT you are to install is version 3.51 or higher.♦ Since Windows NT doe

- 16 -Click “Add” button, and click “Have Disk...” button. Windows NT willthen prompt you to insert the manufacturer installation disk. Insert thede

- 17 -INSTALLATION FOR PARALLEL PORT INTERFACEHARDWARE INSTALLATIONBefore you begin, make sure you turn OFF all power to your system beforeconnecting

- 18 -4. Plug-in the AC adapter to a working AC receptacle. Turn on thePortable CD-ROM power before your turn on PC power.NOTE:Always, turn the Portab

- 19 -SOFTWARE INSTALLATION FOR WINDOWS 95/98Check all the connection as stated in the “Hardware Installation” section.From the Desktop Click ‘My Comp

- 1 -CONTENTSPRECAUTIONS ... 1PART NAMES AND FUNCTIONS...

- 20 -3. Open "SCSI controllers". Click "Have Disk...". 4. Insert Installation Diskette into the drive selected, then click

- 21 -INSTALLING THE PCMCIA CD-ROM FOR WINDOWS NTIn Windows NT 4.0, you may select “Control Panel” under “Settings” fromthe “Start” menu to open the “

- 22 -Click OK to select the driver.Follow the on-screen instruction to continue. After finishing, Windows NTwill prompt you to restart your computer

- 23 -USING THE PCMCIA CD-ROMBASIC OPERATING PROCEDURE1. Make sure there is power to your drive.2. Push gently but firmly, the eject button on the fro

- 24 -5. Hold down the drive and gently push the panel to close the tray.6. Wait for a few seconds before the disc is ready to be accessed.7. To remov

- 25 -Playing an Audio CD by CD player Utility in Windows 951. Connect the 3.5mm stereo audio cable from the Line-Out Jack of yourCD-ROM to your note

- 26 -To display the PC card indicator on the task bar, perform the followingsteps,1. Double-click the PC Card (PCMCIA) icon on the Control Panel.2. M

- 27 -APPENDIX AIF SOMETHING GOES WRONGFollowing are the solutions for some of the problems you may encounterwhile using the Portable CD-ROM.NOT ABLE

- 28 -APPENDIX BSOFTWARE INSTALLATION FOR DOSPCMCIA InterfaceAutomatic InstallationThe INSTALL program helps you install the device driver into yourco

- 29 -Manual InstallationYou may also manually install the Portable CD-ROM device driver if thedefault setting conflicts with your system. Please foll

- 3 -PRECAUTIONSREAD THIS SECTION CAREFULLY BEFORE STARTING TO USE THE PORTABLE CD-ROM.ýŸ Do not place heavy objects on the drive.ýŸŸ Do not expose

- 30 -The example above shows the default setting. The /D: switchindicates the device name. It MUST be the same name as youspecified by the /D: swit

- 31 -video card. Refer to the side of the CD-ROM package for programrequirements, and enjoy!Access TransCD without Software Installation(Dynamic loa

- 4 -• Condensation can form on the lens if the CD-ROM drive is movedfrom a cold temperature to a warmer environment. This can result inthe lens inab

- 5 -PART NAMES AND FUNCTIONSFRONT PANELThe front panel of your CD-ROM may look slightly different from thefigure shown below. The important parts and

- 6 -REAR PANEL1. Power Button:Press the button to manually power on/off the drive when it is poweredby an AC adapter.2. DC in Jack:This jack connects

- 7 -PARALLEL PORT ADAPTER CABLE:•• Parallel port connector:Connect this connector to a computer (25 pin) parallel port (Printerport).‚‚ CD-ROM driv

- 8 -supply enough power to operate the CD-ROM drive, you must use theexternal power as described below.When the POWER SOURCE SWITCH is set to “DC” as

- 9 -INSTALLATIONThe installation procedures have two sections for each type of interface.1. PC Card (PCMCIA) interface2. Parallel Port interfaceThe p