Exp-computer CRW with CDROM Card Manual de usuario

User’s Manual

- 4 -Rear Panel Of The CD-RW Drive 1. Power Button: Press this button to manually power on/off the CD-RW drive. 2. Power Jack (DC IN): Connect the

- 5 -External Type Ultra-Slim Type

- 6 -HARDWARE INSTALLATION Note: ♦ This external CD-RW should only be powered by the AC adapter provided by manufacturer, using an incorrect AC a

- 7 -External Type Ultra-Slim Type

- 8 -SOFTWARE INSTALLATION FOR WINDOWS 95/98 The following installation procedures are extracted from the Windows 98SE installation. The installat

- 9 -5. Select ‘Floppy disk drives’ box and insert the device driver diskette into floppy drive. Click Next. 6. Select ‘The updated driver (Recom

- 10 -9. Windows will then detect the CD-RW drive, you will find a new drive letter has been assigned for the drive in ‘My Computer’. 10. If the

- 11 -SOFTWARE INSTALLATION FOR WINDOWS Me Windows Me will install the external CD-RW with its resident driver, please do not insert the device dr

- 12 -4. Windows will install its resident driver – ‘Standard IDE/ESDI Hard Disk Controller’ for the external CD-RW. After the necessary files are

- 13 -SOFTWARE INSTALLATION FOR WINDOWS 2000/XP 1. Boot-up your computer into Windows, making sure the device driver for ‘PCMCIA Adapters’ has be

- 14 -SOFTWARE INSTALLATION FOR WINDOWS NT Note: ♦ Make sure the Windows NT system is version 3.51 or higher. ♦ Since Windows NT does not suppor

- 15 -4. Click Have Disk button to continue. Windows NT will then prompt you to insert the manufacturer’s driver diskette. Insert the device driver

- 16 -SOFTWARE INSTALLATION FOR DOS/WINDOWS 3.1 Automatic Installation Follow the instructions below to proceed with automatic installation. 1.

- 17 -6. The rest of the installation should proceed automatically, the CONFIG.SYS and AUTOEXEC.BAT files on your computer will be updated automati

- 18 -ARICDI.EXE is the device driver for the PCMCIA CD-RW. The parameters of ARICDI.EXE are described below: /P is used to set the I/O ports, and

- 19 -After rebooting your computer, the following messages will be displayed on your screen, which are generated by ARICDI.EXE and MSCDEX.EXE. Conf

- 20 -♦ Error: Illegal IRQ number! The above message means invalid IRQ number in the ARICDI line of CONFIG.SYS have been selected. The legal IRQ nu

- 21 -SOFTWARE INSTALLATION FOR OS/2 WARP Before installing the external CD-RW device driver for OS/2 WARP, make sure your computer is PCMCIA supp

- 22 -Manual Installation You may also manually install the external CD-RW OS/2 device driver if the default setting conflicts with your system. Pe

- 23 -1. Open OS/2 System ! Open System Setup ! Open Selective Install. 2. Check if PCMCIA Support has been installed in the System Configuration

FCC COMPLIANCE STATEMENTS This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

- 24 -USING CD-RW WITH PCMCIA INTERFACE To Connect The PCMCIA CD-RW To Your Computer ♦ Windows 95/98/Me/2000, and WindowsXP: 1. Boot into the W

- 25 -3. Wait for few seconds until the system prompts ‘The device can now be safely removed from the system’. Click OK, and then remove the PC Car

P/N: 7450317-01

TRADEMARKS PCMCIA are the trademarks of Personal Computer Memory Card International Association. MS-DOS, Windows, Windows 95/98/Me/2000/XP/NT and

CONTENTS INTRODUCTION ... 1 SYSTEM REQU

- 1 -INTRODUCTION The external CD-RW is a high performance external CD Recordable/ReWritable drive, it can be easily connected to computer by usin

- 2 -PART NAMES AND FUNCTIONS Your external CD-RW may differ slightly from the figures shown, however the controls will operate as described below

- 3 -External Type Ultra-Slim Type