EXP Computer CD Traveler Manual de usuario

CDG-821USER’S MANUALEXP COMPUTER, INC.

- -5POWER SOURCEThe CD TRAVELER can be either powered by the AC adapter or by thebatteries as a flexible option. However, the AC adapter has a p

- -6INSTALLING THE BATTERIESThe CD TRAVELER requires eight AA size batteries (not included) foroperation. When using alkaline batteries, the batt

- -7Figure 4REMOVING THE BATTERIES1. Remove the battery lid by sliding the cover in the direction of thearrow as shown in Figure 3.2. Lift up the

- -8HARDWARE INSTALLATIONINSTALL THE CD-ROM WITHOUT THE GAME ADAPTER1. Connect the PCMCIA interface card to the CD-ROM drive. Pressfirmly until

- -9INSTALL CD-ROM WITH THE GAME ADAPTER1. Connect the game adapter to CD-ROM drive, and tighten the twoscrews on the game adapter. 2. Connect th

- -10SOFTWARE INSTALLATION FOR DOS/WINDOWS 3.1The INSTALL program helps you install the device driver into thecomputer easily. Please follow the

- -11 SOFTWARE INSTALLATION FOR WINDOWS 95If your computer does not have Windows 95 installed yet, please refer tothe section titled “Using CD TR

- -12Follow the on-screen instruction to continue. After finishing, rememberto shutdown Windows and restart your computer if you are using the CD

- -13GAME-PAD CONTROLLER DESCRIPTIONNOTICE1. The I/O address 200-207 of your computer must be available, or theGame port will not work properly.

- -14USING CD TRAVELER TO INSTALL WINDOWS 95If you are about to upgrade your operating system from DOS/Windowsto Windows 95 using the CD TRAVELER

EXP COMPUTER, INC. EXP MEMORY PRODUCTS.NON-TRANSFERABLE LIMITED WARRANTYEXP COMPUTER INC., AND EXP MEMORY PRODUCTS("EXP")warrants that the Q

- -15ENABLING 32-BIT CARD SUPPORT OF WINDOWS 95Your system should be ready for PCMCIA socket support prior tooperating the CD TRAVELER. To check

- -16Figure 10After the PCMCIA 32-Bit Card support is installed, Windows will ask youto reboot your computer. Then you should refer to the first

- -17USING THE PCMCIA CD-ROM WITH A COMPUTER Make sure the AC adapter is properly connected or the batteries areinstalled.CAUTIONConnect the PCMC

- -18The CD-ROM for the Windows 95 titles include the AUTO RUN feature.This means when you close the disc cover with this type of CD discinside,

- -19Be sure you are removing the card by the procedures described above,otherwise, the following dialog will be displayed: (Figure 15)Figure 15T

- -20HOW TO PLAY THE AUDIO CDWindows 3.1The CD-Audio CDs can be played on your PCMCIA CD-ROM by using CDAudio software utilities, such as the Me

- -21TROUBLE SHOOTINGWindows 95The Windows 95 32-bit mode plug-n-play drivers will automaticallyallocate the hardware resources for CD Traveler,

- -229. Click “OK” when finishing, system may ask you to reboot thecomputer to enable the new settingsRemove or re-install the driverIf you want

- -23DOS/Windows3.XAfter rebooting your computer, the following messages will be displayedon your screen, which are generated by EXPCDG.EXE andMS

- -24EMM386 line of CONFIG.SYS to exclude at least 4K memory formapping. For example, DEVICE=C:\DOS\EMM386.EXE ... X=D000-D3FFv v Error: The I

FCC COMPLIANCE STATEMENTSThis equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FC

- -25 PCMCIA(PC CARD) SOFTWARE INFORMATIONIf you have installed the PCMCIA software, such as SystemSoft’sCardSoft or Databook’s Cardtalk, then EX

- -26The device driver names of the major PCMCIA software are listedbelow:Software/DeviceDriverSystemSoftCardSoftPhoenix AwardCardwareIBMThinkPad

- -27POWER SAVINGThe CD TRAVELER may operate with an AC adapter or batteries. Useof the supplied AC Adapter will provide the power for use as a

TRADEMARKSSystemSoft is a registered trademark of SystemSoft Corporation.CardSoft is a trademark of SystemSoft Corporation.Phoenix is a registered tra

CONTENTSINTRODUCTION... 1SYSTEM REQUIREMENTS...

- -1INTRODUCTIONThe CD TRAVELER brings the latest in mobile computing technology tonotebook computer users with portability and convenience. The C

- -2PART NAMES AND FUNCTIONSFRONT PANEL OF THE CD-ROM DRIVE•• Disc Tray:This disc tray is used to insert the compact disc.‚‚ Load/Stop button:• P

- -3 REAR PANEL OF THE CD-ROM DRIVE•• Interface Connector:This interface connector connects to the PCMCIA interface card.‚‚ DC in Jack:This jack

- -4GAME ADAPTER•• CD-ROM Connector:This connector connects to the CD-ROM drive.‚‚ Game Port:This port connects to joystick or game-pad.ƒƒ PC Car